Aldi L122AA63H11A6.5W
Model | L122AA63H11A6.5W |
Vendor | Aldi |
Description | LIGHTWAY smart home LED-lamp - candle |
Exposes | light (state, brightness, color_temp, color_xy), effect, do_not_disturb, color_power_on_behavior, linkquality |
Picture | ![]() |
Notes
Pairing
Factory reset the light. After resetting the light it will automatically connect.
The light should be turned off for at least 10 seconds. After that, the on- and off-phases should last around 2 to 5 seconds. Start with light on, then off, and then 3 “on’s”, wait in the 3rd ON state.
Options
transition
: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to0
(no transition). The value must be a number with a minimum value of0
color_sync
: When enabled colors will be synced, e.g. if the light supports both color x/y and color temperature a conversion from color x/y to color temperature will be done when setting the x/y color (default true). The value must betrue
orfalse
state_action
: State actions will also be published as 'action' when true (default false). The value must betrue
orfalse
Exposes
Light
This light supports the following features: state
, brightness
, color_temp
, color_xy
.
state
: To control the state publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"state": "ON"}
,{"state": "OFF"}
or{"state": "TOGGLE"}
. To read the state send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"state": ""}
.brightness
: To control the brightness publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"brightness": VALUE}
whereVALUE
is a number between0
and254
. To read the brightness send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"brightness": ""}
.color_temp
: To control the color temperature (in reciprocal megakelvin a.k.a. mired scale) publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"color_temp": VALUE}
whereVALUE
is a number between150
and500
, the higher the warmer the color. To read the color temperature send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"color_temp": ""}
. Besides the numeric values the following values are accepected:coolest
,cool
,neutral
,warm
,warmest
.color_xy
: To control the XY color (CIE 1931 color space) publish a message to topiczigbee2mqtt/FRIENDLY_NAME/set
with payload{"color": {"x": X_VALUE, "y": Y_VALUE}}
(e.g.{"color":{"x":0.123,"y":0.123}}
). To read the XY color send a message tozigbee2mqtt/FRIENDLY_NAME/get
with payload{"color":{"x":"","y":""}}
. Alternatively it is possible to set the XY color via RGB:{"color": {"r": R, "g": G, "b": B}}
e.g.{"color":{"r":46,"g":102,"b":150}}
{"color": {"rgb": "R,G,B"}}
e.g.{"color":{"rgb":"46,102,150"}}
{"color": {"hex": HEX}}
e.g.{"color":{"hex":"#547CFF"}}
Transition
For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property transition
to the payload which is the transition time in seconds. Examples: {"brightness":156,"transition":3}
, {"color_temp":241,"transition":1}
.
Moving/stepping
Instead of setting a value (e.g. brightness) directly it is also possible to:
- move: this will automatically move the value over time, to stop send value
stop
or0
. - step: this will increment/decrement the current value by the given one.
The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up. To do this send a payload like below to zigbee2mqtt/FRIENDLY_NAME/set
NOTE: brightness move/step will stop at the minimum brightness and won't turn on the light when it's off. In this case use brightness_move_onoff
/brightness_step_onoff
{
"brightness_move": -40, // Starts moving brightness down at 40 units per second
"brightness_move": 0, // Stop moving brightness
"brightness_step": 40 // Increases brightness by 40
"color_temp_move": 60, // Starts moving color temperature up at 60 units per second
"color_temp_move": "stop", // Stop moving color temperature
"color_temp_step": 99, // Increase color temperature by 99
}
Effect (enum)
Triggers an effect on the light (e.g. make light blink for a few seconds). Value will not be published in the state. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"effect": NEW_VALUE}
. The possible values are: blink
, breathe
, okay
, channel_change
, finish_effect
, stop_effect
.
Do_not_disturb (binary)
Do not disturb mode, when enabled this function will keep the light OFF after a power outage. Value can be found in the published state on the do_not_disturb
property. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"do_not_disturb": NEW_VALUE}
. If value equals true
do_not_disturb is ON, if false
OFF.
Color_power_on_behavior (enum)
Power on behavior state. Value can be found in the published state on the color_power_on_behavior
property. It's not possible to read (/get
) this value. To write (/set
) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set
with payload {"color_power_on_behavior": NEW_VALUE}
. The possible values are: initial
, previous
, cutomized
.
Linkquality (numeric)
Link quality (signal strength). Value can be found in the published state on the linkquality
property. It's not possible to read (/get
) or write (/set
) this value. The minimal value is 0
and the maximum value is 255
. The unit of this value is lqi
.